1 l of a ride pdf download

Use a flat head screwdriver to gently pry the LEFT side of foot pedal. Gently remove the foot pedal. Disconnect the old foot pedal from the pedal switch socket. Replace and reconnect the new foot pedal to the pedal switch socket to ensure they are connected in the correct position see Figure 3 and then insert the right side of the foot pedal into the foot pedal compartment first, and gently push down on the left side of the pedal so that it snaps into place.

Unscrew the two screws on the seat and remove the seat. Unscrew four 4x12 round head screws as shown to remove the Forward-Reverse Shifter Assembly from the ride-on toy body diagram A.

Park the ride-on toy indoors or cover it with a tarp to protect it from wet weather. Keep the ride-on toy away from sources of heat, such as stoves and heaters. Plastic parts may melt. A new battery should have does not run battery been charged for at least 18 hours before using the ride-on toy for the first time.

After first-time use, recharge the battery for at least 12 hours after each use. Make sure the was running connectors battery connector is tightly plugged into the but suddenly control module connector, and that there are no stopped loose wires around the motor.

A new battery should have sluggishly been charged for at least 18 hours before using the ride-on toy for the first time. We respect your privacy. Any information collected by Dynacraft Wheels will never be shared with any other company or organization. See Dynacraft's privacy policy for further information: dynacraftwheels. Page 33 This Warranty is not transferable to anyone else and is the only warranty for your Dynacraft product, to the extent permitted by law No other express or implied warranty is given, and except to the extent prohibited by applicable law, any implied Print page 1 Print document 35 pages.

Rename the bookmark. Delete bookmark? The park-and-ride would serve multiple local and express bus routes. Skip to main content. North Glendale Park-and-Ride. Glendale Valley Metro, in partnership with the cities of Glendale and Peoria, is conducting a study to identify a park-and-ride location to serve riders of Express Routes and and meet the transit needs of the Northwest Valley.

Align the tabs on the back of the Edge with the bike mount notches. Press down slightly and turn the Edge clockwise until it locks into place. GPS is turned off. Heart rate monitor is active. Speed and cadence sensor is active. Power meter is active. Press any button to extend the backlight for 15 seconds. After completing your ride, press STOP. Using Free Software Follow the instructions included with the software. Page Training With Your Edge 5.

Enter a time, distance, or calorie amount. Go for a ride. Each time you reach the alert amount, the Edge beeps and displays a message. Select Auto 3. In the select 4. Enter a value. Customize optional lap data fields page 6. Auto Lap Trigger field, Distance. Page Using Auto Pause 4. The training data pages scroll to pause automatically. You can press to manually switch pages.

Page Courses You can add course points, or places on your course that you want to remember, such as water stops or distance goals. Page 18 5. History is recorded even if you are not on the course. Page Workouts After you create a workout, you can use Garmin Connect or Garmin Training Center to schedule the workout for a particular day.

You can plan workouts in advance and store them on your Edge. Page 21 If you select Open, you can press to end the step during your workout. If necessary, enter a value in the field below Duration. Select during the step. Page 22 A message appears, counting down the time or distance until a new step begins.

PAGE to view the data pages: to end a step early. Page 23 To make a permanent change to a workout, edit the workout in Garmin Connect or Garmin Training Center and then transfer it to your Edge.

Press and hold MENU. Press the tab down. Wet both electrodes on the back of the heart rate monitor to create a strong connection between your chest and the transmitter. NOTE: Contact your local waste disposal department to properly dispose of batteries.

Locate the circular battery cover on the back of the heart rate monitor. Page Installing The Gsc 10 6. Page 30 The spoke magnet can face away from the GSC 10 if there is not enough room between the sensor arm and the spoke.

The spoke magnet must line up with the indication line on the sensor arm. Page 31 7. Move the sensor arm to within 5 mm of the spoke magnet.